Sony CDXGT930UI CD Receiver Motorized, full-motion, fluorescent four-line display (Black)

Sony CDXGT930UI CD Receiver Motorized, full-motion, fluorescent four-line display (Black)

Sony CDXGT930UI CD Receiver Motorized, full-motion, fluorescent four-line display (Black)

Bad Luck Continue Unit Head / Bad The saga continues. I bought this HU over a month ago and finally time to install it. Gone through a lot of trouble for nothing. The control unit is as good as something to be exploited. It turns out, but that's it. At least I put my voltmeter on my hyundai for a better place.

If you have little money, but want a better stereo shop in the car, installing a stereo system itself, you can create a huge amount of money. It 's relatively easy to install a new CD player or radio in the car, especially if you have no experience in wiring and electronics.

The standard radio system is integrated into the dashboard, then this article will take the necessary measures to provide this function. Custom or modified vehicles require a differentA set of instructions for stereo. For this task, you need a new car radio or CD player (also called unit), wire stripper, electrical tape, a set of screwdrivers and wire cutters. You'll also need a guide that explains how to remove the dashboard and remove the old stereo system depending on without causing any damage. If you follow these simple steps, you will enjoy your new stereo in no time!

Pioneer Wiring Harness

1) Buying a new stereo system. Buying one that fitscorrect, where was the old one. Also, when buying a stereo, you might want to get to a specific harness that is specific to your stereo and your new make and model of vehicle. Harnesses to do all the work a snap, literally.

2) Make sure the engine is off. Disconnect the negative (black) battery cable. Never a part of the electrical system connected to the battery of your car to work, because the shock could be fatal.

3) AfterRemove the manual, the panel next to the stereo. Loosen and remove your old stereo (head) unit. On the back of the device or there is a stack of individual wires or a single connector that connects a lot of wires. If you find a lot of wires, which are not engaged yet. You have to do a few at a time when, to avoid confusion.

4) electric cables to connect manually or with the sling. If you have a step belt 5, thenStep 9 to continue. If you do not have a harness, skip step 5 and follow steps 6-8

5) Connect the new wiring into the outlet, if you are able to make a purchase they were. This kit is then connected to the back of your new car stereo. If you are able to do it, then you can skip steps 6-8.

6) Do you have any wires to connect manually, if you do not buy a harness. Connect the positive cable from each speaker to make positive connectionson the back of your stereo system first. Then negative wires from each speaker connected to the negative terminals on the stereo. If you're going to find a single cable from each speaker so that they were grounded to the frame. If this is the case, then the new speaker cables are installed.

7) Close the '(earth) wire to the stereo system -/black for a bolt or screw which is mounted close to the stereo in the dashboard. This attachment must be metal, not fiberglass or plastic.

8)Connect both + /-wire power cord and red power constant 12 with the new radio. Read the installation instructions for the proper positioning of these wires.

9) You should now have a unique connector to the cable that come together to right the vehicle, both through the new connection in steps 6-8, or from the saddle.

10) Slide the new stereo in your support, whose connection with the purchase must be included. In some cases, you must use the oldOriginal owner of your stereo.

11) Connect the wiring connector on the back of your new radio or CD player. They should hang a missing single wire, the old system off. This wire is your antenna. Connect this wire on the stereo again. You can also see a wire antenna power, which must be connected.

12) Slide the stereo in the dash compartment. Try it before screwing it in Connect the battery cable. Start the engine to power theStereo. Turn on some 'music and listen to the performance of each speaker. If everything seems to work well, screw in place and replace your home stereo to cover your bar.

Sony CDXGT930UI CD Receiver Motorized, full-motion, fluorescent four-line display (Black)